Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
How do you really feel in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a tub isn't exactly rocket science, but it does need solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately hard job. If the old bathtub is readily easily accessible, the task can relocate easily; if you have to open up a wall surface to get rid of the old bathtub and place the new bath tub, the task is much harder. In either situation, the job is within a home handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the brand-new one. See to it you have actually qualified on your own for the work and fit trying it. Instead of working with a professional to take over a halfway-completed job, it is far better to take into consideration utilizing one before you start. Chances are you might need a specialist plumber to make tube links.
This short article will aid you set up a new bathtub in your restroom if you have currently gotten a brand-new bathtub and also don't require to alter the setup of your previous water pipes.
Your devices and product checklist must make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, activate the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the restricted access that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will come from the pipelines. When the supply pipes have been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before carrying on to fit the new taps, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Protect the faucet in position with the supplier given backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The former kind needs to be connected to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Tub
Making use of both wood boards under its feet, place the bathtub in the required placement. The wood boards are practical in equally spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bathtub up until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest versatile tap adapter to the proper supply pipeline by making a compression sign up with; after that do the same for the various other tap.
Activate the water system and inspect all joints and also brand-new pipework for leaks and tighten them if essential. Load the bathtub and additionally examine the overflow outlet and also the typical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's user's manual. Tiling and sealing around the tub should wait until the bath tub has actually been used a minimum of when as this will settle it right into its last position.
Preparing for the Installation
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to avoid strain on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final position.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, triggering the water to pass through the wall between the bath and also the tiling, resulting in problems with moisture and feasible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily readily available on the market. It is suggested to fit the floor tiles using waterproof or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our part about Tools You Need to Install a New Bathtub . Thanks a ton for finding the time to read through our piece of content. In case you liked our article please do not forget to pass it around. I praise you for your time. Visit again soon.
Find Out More Report this page